Adding white lines to break up translation units
Waze has enabled Speed Limits in the editor (WME). This function will only be activated in the Waze app (4.0) when there are enough roads that have this info.
Therefore the Waze editing community is making an extra effort to add the info as soon as possible.
Everybody will gain from this common effort, the editing community and the Waze users. There will be enough editable segments for all editors.
== Guidelines for the (new) editor ==
* Initially speed limits should be entered on segments locked at your own level. As an incentive to the vast amount of beginning Waze editors, Waze rewards the efforts of entry-level editors by earning edit points by assigning them this task. Advanced editors, please leave the lower level segments for the editors with a lower level.
* Make sure you’re using the correct units for the speed limits! You can switch between Imperial and Metric by clicking on the tab with the ‘Gear’ icon, on the left column in the Waze Map Editor. The Gear icon is only visible when no segment or place is selected.
* Adding Speed Limits must be based on certainties. You should be familiar with the area where you add them. Please do not enter Speed Limits when you are not 100% sure.
== How to ==
=== Cutting segments to add speed limits ===
* Enter the correct speed limit for each separate segment.
* Try to cut the segment as close to actual point of speed limit-change.
* When speed limit changes close to an existing junction node, it might be better not to cut.
: Keep in mind that segments should be at least '''20m''' long.: In some cases this length might even be longer, try to take the intent behind the placment of road signs in to account.
* Street names have to remain unchanged to allow for correct guidance.
* Segments with closures can’t be edited, so it is impossible to add a Speed Limits while the lock is in place. Editors with closure permissions have a procedure to add Speeds anyway.
Because it takes less effort to do the edit without having to unlock or remove a closure, it is better to simply request for the change.
These requests can be made through the known Benelux community communication channels.
Information to provide: Permalink ([http://bit.ly/1R0Frhh How to make a permalink]), Required speed limit (with directions) and if applicable, also add cutting instructions.
=== Private Roads ===
* Private Road segments do not show the speed limit. You cannot add speed limit-info.
* If you select Private Road segments and change the type to Street, the speed limit can be added. Switch back to Private Road and Save. The speed limits will be saved (although not visible in the app). At this moment it’s unclear if the Waze app will use this hidden information.
=== Roundabouts ===
Add the highest speed of the connected roads that have the same road type as the roundabout. If unclear use the default speed of the current zone.
=== Reduced speed zones ===
A reduced speed zone has a restricted speed in a well defined area.
* Care should be taken defining the boundaries of such zones.
* In Belgium a school safety zone is a special application of a Zone 30. These zones can be marked by a permanent or dynamic ‘zone 30’ sign. In both cases the lowest speed must be entered.
=== Highways with MTM (Motorway Traffic Management) ===
The normal (maximum) speed must be entered.
== Tips & tricks ==
* When you are not sure about a certain edit to add a Speed Limit, contact your country managers. They can use the edit as an example for all editors.
* Do not include multiple road types in one selection or the speed limit text boxes will disappear.
* Existing Speed Cameras can be used as reference points. The speed at these points has been confirmed when the Cameras were added.
== WME scripts ==
Before you can use WME scripts, you should install a userscript add-on for your browser. The following [https://greasyfork.org/en/help/installing-user-scripts link] explains how to do that.
* WME Speedhelper ([https://greasyfork.org/en/scripts/13774-wme-speedhelper Link])
: Designed to simplify the input of the speed limits* WME Speeds ([https://greasyfork.org/nl/scripts/12402-wme-speeds Link]) : Shows the Speed Limit of each segment using a color code. Can be used to visualise where Speed Limits have been added.* WME Color Highlights ([https://greasyfork.org/en/scripts/3206-wme-color-highlights Link]) : Version 2.3 (and later) supports highlighting of segments without verified speed limits.
* WME Route Speeds ([https://greasyfork.org/en/scripts/5402-wme-route-speeds Link])
** Do not use this method as a primary source of information, only as an aid! Use for longer stretches of segments.
** Helps to get an indication of the real speed limit.
** Can help to determine where a change in the speed limit might occur.
:: Try to avoid periods with heavy traffic (peak hours) and look in both directions.* Street Vector Layer ([https://www.waze.com/forum/viewtopic.php?f=819&t=149535 Link]) : Can be used to show the segments that already have speed-information. : Click on ‘Street Vector’ at the bottom of the screen to bring up the configuration display.