Minnesota/Special roads/Main: Difference between revisions Discussion View history

Line 15: Line 15:
Keep in mind that if the person does allow for dirt roads, Waze will treat the road as a Primary Street so do not try to make an exception to well maintained dirt roads as a street or you will cause the driver to be directed on undesirable roads. Yes, that's right, a dirt road can be seen as a higher priority than a street! This is very important in rural areas where the Street Category should only be used on very short road segments that are paved.  In towns, the Dirt Road Category should be rarely used and an unpaved road should be considered a street or a private road.
Keep in mind that if the person does allow for dirt roads, Waze will treat the road as a Primary Street so do not try to make an exception to well maintained dirt roads as a street or you will cause the driver to be directed on undesirable roads. Yes, that's right, a dirt road can be seen as a higher priority than a street! This is very important in rural areas where the Street Category should only be used on very short road segments that are paved.  In towns, the Dirt Road Category should be rarely used and an unpaved road should be considered a street or a private road.


=== Private Road[[File:Service road.png|200px|Service road.png]] ===
==== Private Road[[File:Service road.png|200px|Service road.png]] ====


[[File:Pi gated-community1.jpg|right|300px|Pi gated-community1.jpg]]
[[File:Pi gated-community1.jpg|right|300px|Pi gated-community1.jpg]]

Revision as of 17:07, 13 March 2015


Other drivable roads

Dirt Road / 4X4 TrailService road.png

In the state of Minnesota, most unpaved roads are considered dirt roads. Knowing this will help you create the correct road levels. Undrivable roads should not be mapped, should be restricted, or should be listed as a trail instead and not be connected to any functional roads. Even though 4x4 is in the title, we will only use dirt roads for standard gravel or dirt roads that most vehicles can drive on. Keep in mind that because of the way Waze handles dirt roads, we will not use the dirt road class in the city limits of any town over 500 people. Any in-town gravel roads will be streets.

Because most likely people in Minnesota feel a gravel road is a dirt road, we will use Dirt Road for both examples. Please be aware of any of these dirt roads that are minimum maintenance roads as these roads should have restrictions in place for winter months.

The reason the dirt roads classification is important is because a user can decide to not be sent on dirt roads or to only be sent on dirt roads for short distances in the settings of the Waze App.

Keep in mind that if the person does allow for dirt roads, Waze will treat the road as a Primary Street so do not try to make an exception to well maintained dirt roads as a street or you will cause the driver to be directed on undesirable roads. Yes, that's right, a dirt road can be seen as a higher priority than a street! This is very important in rural areas where the Street Category should only be used on very short road segments that are paved. In towns, the Dirt Road Category should be rarely used and an unpaved road should be considered a street or a private road.

Private RoadService road.png

Pi gated-community1.jpg
Pi gated-community1.jpg

Private Roads should follow the Wiki Example on Private Roads. Please be very limited on using this for driveways as, for the most part, these should not be mapped at all.

Keep in mind that on the Waze App, a private road will look like a street. Nothing looks more off than a bunch of streets connected to a dirt road.

If you are adding a private road for a private housing section, make sure house numbering is correct or there is a place point or area within a private road section. This area will still be able to be navigated to the correct destination as long as it has a proper address to navigate to. Pay attention to this article for more information

Alleyways

Avoid drawing alleyways unless it is considered a street by the general public. Most alleyways should not be used to direct traffic and will cause unneeded nodes in the road that can cause roads connected to the alleyways to be less desirable. Most alleyways that would ne mapped will use the Parking Lot class.

Roundabouts

Minnesota has been adding roundabouts in many locations throughout the state. It is important to note that most roundabouts should only have three to four connections or it will sound confusing to a driver. Following this Example will give proper turn information and roundabout icons on the screen. If you would use multiple-point access, it instead will say the exit number such as, "At the Roundabout, take the 3rd exit".

This is an indication of what a user of Waze should see on an upcoming Roundabout. It is clear at showing the direction of the turn. It also will verbally say what is referenced on the signage such as "At the Roundabout, Continue Straight" or "turn left". This is the Minnesota Standard for creating and editing Roundabouts.



This is how it looks when more than four exit points occur. It does not give clear guidance to the driver on what way to go aside from the highlighted road ahead. This should be avoided, Only add multiple connections per side if the signs clearly mark Exit numbers (Commonly seen on signs showing 5 or more exit points).


Roundabouts will use the same functional class of the main route traveling through the roundabout. Follow This Article for more information.

If at all possible, drive through a roundabout after it has been created or updated. Verify that it seems to give correct information.

Other drivable roads

Railroad Service road.png

RoadPicN11.jpg
RoadPicN11.jpg


Railroads are not yet added to the map, but these can be added to prepare the maps for when it is. Mapping the tracks allows Waze to recognize spurious speed data from people Wazing on the train and prevent it from corrupting speed data for the adjacent road.



Please notice that railroads have changed from previous interpretations of railroad mapping. Even veteran editors need to pay attention to this section!


  • Elevation will be set to the same elevation standards as a drivable road. When tracks junction a road on the ground, the Elevation should be set to Ground.
  • If the railroad crosses a segment of road, it should be connected to the road to so the historical data for the rail crossing will be more accurate.
  • Always select "None" for the city name. This avoids city smudging.
  • Set railroad to 2-way directionality and Restrict turns to and from the railroad segments.
  • Follow the Federal DOT Railroad GIS to verify the owner of the rail line to help on naming of the segment. Use the acronyms under RROWNER1 to help on naming.
  • Name each segment using the rail owner name acronyms or abbreviations railroad. For example, Twin Cities & Western Railroad uses TCWR. We would name this section TCW Railroad. We leave off the R in the acronym because it would be redundant to say, Twin Cities & Western Railroad Railroad.
  • Canadian Pacific uses the acronym CPRS, but it is more know as CP, so it will be called CP Railroad
  • Do not map every piece of parallel track, such as in sidings or yards, or industrial spurs that don't cross any roads. Your work may otherwise be seen as clutter, much like mapping every parking lot row.
  • Lock all railroads to a Level 2
  • Read this section for more information about railroads.

Runway/Taxiway

Please follow this Wiki article on Runways for information about how to set runways correctly. These roads should be locked to the same standard as Airport Area itself.