Speed Cameras View history

Revision as of 11:18, 25 September 2012 by Dave2084 (talk | contribs) (→‎Confirming a Camera in Waze Map Editor: changed confirm to approve)

DRAFT DRAFT DRAFT DRAFT DRAFT DRAFT DRAFT

This Page is in DRAFT Status and should not be used for reference when editing the Waze Map

Introduction

This page forms part of UK Editing Best Practice. Editors are encouraged to follow these guidelines.

Waze currently supports reporting of and warning for three categories of Cameras: Speed Cameras, Red Light Cameras and Fake Cameras. This Wiki page aims to help the Wazer identify, map and approve cameras in the Client and Map Editor.

Waze Camera Types

Speed Cameras

Fixed speed enforcement camera locations of any type (Gatso, Peek, Truvelo, Monitron or SPECs).

Notes:

  1. Until Such time as Waze supports SPECs Cameras natively these should be recorded as a standard camera at each location (entry point, mid point(s) and exit point).
  2. Mobile speed cameras should not be reported in Waze, instead use the Report -> Police feature in the client.

[Be aware when using Report -> Police to report a mobile speed camera that there have been recent cases of motorists being prosecuted for flashing their headlights to warn other drivers that they are approaching a mobile speed trap. Whilst there have been no recorded cases of a Wazer (or other App user) being prosecuted you could potentially be liable for prosecution for reporting in this way!]

Red Light Cameras

Red light camera locations of any type (Gatso or Monitron).

Note: Some red light camera locations monitor speed as well as driving though a red light. If this is the case then the speed in km/h should be recorded.

Fake Cameras

Fake cameras should only be reported for a dummy camera that is masquerading as a Speed or Red Light Camera as defined above.

Cameras that should be reported

Gatso Speed Cameras

The most common speed camera type found in the UK and are rear facing, when triggered they will flash. They may be mounted on their own post (which may be reversible) or on an overhead gantry (common on motorway variable speed limit zones).

Typically a series of markings are placed on the road in front of the camera often on both lanes to catch drivers overtaking or driving on the wrong side of the road. These marking may also be behind the camera, this is a good indication of a reversible camera.

Where aerial photography is of good enough quality the camera and it's road markings can be seen and used to aid correct placement of the camera.

Front of Gatso Camera
[Image by: Dave2084]
Rear of Gatso Camera
[Image by: Dave2084]
Gatso Camera Close-Up
[Image by: Dave2084]
Aerial view showing road markings
[Image taken from Waze Map Editor]
Gatso Camera Road Markings
[Image by: Dave2084]
Placement in Waze Map Editor
[Image taken from Waze Map Editor]

Peek Speed Cameras

Similar to Gatso cameras, also rear facing and when triggered they will flash. [IMAGE]

Truvelo Speed Cameras

Truvelo cameras differ from Gatso and Peek cameras in that they front facing, since they are Infra Red when triggered you will NOT see any flash. Additionally they can also be configured in a rear facing arrangement although this is not common.

Typically the road is marked with three white lines in front of the camera across one or both lanes. These markings may also be behind the camera, this is a good indication of a reversible camera.

Where aerial photography is of good enough quality the camera and it's road markings can be seen and used to aid correct placement of the camera.

Front of Truvelo Camera
[Image by: Dave2084]
Rear of Truvelo Camera
[Image by: Dave2084]
Truvelo Camera Close-Up
[Image by: Dave2084]
Truvelo Camera Road Markings
[Image by: Dave2084]
Aerial view showing road markings
[Image taken from Waze Map Editor]
Placement in Waze Map Editor
[Image taken from Waze Map Editor]

Monitron Speed Cameras

New digital cameras which can be configured as a speed camera and/or a red light camera. [IMAGE]

SPECs Average Speed Cameras

Average Speed cameras. These measuring average speeds between fixed cameras at entry point, mid point(s) and exit point of the monitored zone. [IMAGES]

Gatso Red Light Cameras

Gatso red light cameras are different to their speed detection counterparts and will be triggered when driving through a red light. [IMAGE]

Monitron Red Light Cameras

New digital cameras which can be configured as a speed camera and/or a red light camera. [IMAGE]

Cameras that should not be reported

Mobile Speed Cameras

Mobile speed cameras should not be reported in Waze as by the time they are approved and appear in the client they will be long gone, instead use the Report -> Police feature in the client. [IMAGES]

[Be aware when using Report -> Police to report a mobile speed camera that there have been recent cases of motorists being prosecuted for flashing their headlights to warn other drivers that they are approaching a mobile speed trap. Whilst there have been no recorded cases of a Wazer (or other App user) being prosecuted you could potentially be liable for prosecution for reporting in this way!]

Trafficmaster

Trafficmaster has network of 5,200 traffic flow monitoring sensors used to update their real-time traffic services on UK motorways and trunk roads. These sensors are not used for Speed or red light enforcement and so should not be reported in Waze. [IMAGES]

Congestion Charge Zone Cameras

The London Congestion Charge Zone (CCZ) uses cameras to record vehicles entering or leaving the zone, these are not used for Speed or red light enforcement and so should not be reported in Waze. [IMAGES]

ANPR

Automatic Number Plate Recognition (ANPR) cameras may be used for a number of enforcement functions including: Valid Tax, MoT Test, Insurance and checking criminal activity. At this time however, they are not used for Speed or red light enforcement and so should not be reported in Waze. [IMAGES]

Driver Feedback Signs

Electronic signs that warn you if speeding and may or may not tell you your speed. [IMAGES]

Camera Warning Signs

Signs that warn the drivers of a possible cameras in the area should not be reported. [IMAGES]

Reporting a Camera in the Client

To report a camera, press the report button at the bottom right hand side of the client screen. you will then be presented with the report Menu, from this select "Camera".

All you need to do then is select the camera type and if it applies to your lane or the opposite one. Then simply press send.

Waze v3.x Report Menu
[Image from Waze Client]
Waze v3.x Camera Screen
[Image from Waze Client]
Waze v3.x Camera Screen
[Image from Waze Client]

Notes:

  1. The camera report will be placed on the map where you are when you press the "Report" button, so you can take your time to complete the other details as driving allows.
  2. The camera will only appear on the live map after it has been approved in Waze Map Editor.
  3. Where a location has a camera in each direction, or it is reversible two reports will be required.

Approving a Camera in Waze Map Editor

After a camera has been reported by a Wazer from the client it will not appear on the live map until it has been approved in the Waze Map Editor. Before approval cameras appear in Brown and once approved they change to grey.

Unapproved Approved

Before approving a camera, the editor should consider if there really is a camera there or if the one which has been reported already exists as an approved camera. Many areas of the Waze map are flooded with cameras that are simply not there. Use your judgement, if there is any doubt do not approve it and delete it.

Camera Placement

When reporting a camera from the Waze client it is not always possible to place it in the exact location required. Therefore when approving a camera the editor should examine clues on the map and aerial photography to assist them in moving the camera to the correct position before approving it. You should be aware though that aerial photography (including road markings) and services such as streetview are often out of date so do not rely on them exclusively.

The identification guides for each camera type to be added to the Waze map aim to assist the editor in placing the camera in the correct position. Unfortunately every situation cannot be catered for in this guide so often the editor will have to use their judgement.

To move the camera select it and a circle will appear around it, the camera can then be moved anywhere in the circle. If it needs to be moved further then move it as far as allowed and save. Once saved the circle will be re-centred on the camera again.

Camera Selected
Camera can be moved inside the circle

The red dot in front of the camera indicates the direction of travel and should be the same way (facing the back of the car after it has driven past) regardless of Camera type.

Note: A reversible camera will require two camera reports, one facing in each direction.

Setting the Speed

The the camera is selected you are able to enter the speed in the properties box as shown to the right.

Setting the speed relating to a camera often leads to confusion in the UK since we work in Mph, but the Waze map uses Km/h. When setting speeds refer to the conversion table below (rounded to nearest Km/h) and set the speed accordingly:

Mph 20 30 40 50 60 70
Km/h 32 48 64 80 97 113

Notes:

  1. In managed traffic zones with variable speed limits the speed should be set to the maximum permitted speed. (e.g 70mph=113km/h for the M42).
  2. Some red light cameras such as Monitrons are also capable of enforcing the speed limit as well as driving through a red light. Therefore you should set the speed limit for red light cameras as well as for speed cameras.

Approving the Camera

Once the camera is been positioned and the speed has been correctly set in Km/h check the "Approved" box and save your changes.

The camera will now appear in the live map and on the client once the changes have been processed. Be aware that this may take 2 weeks or more!

DRAFT DRAFT DRAFT DRAFT DRAFT DRAFT DRAFT

This Page is in DRAFT Status and should not be used for reference when editing the Waze Map