Australian Road Names

From Wazeopedia

Revision as of 11:26, 19 July 2012 by Cleary (talk) (Road types)

Introduction

This forms part of Australian Editing Best Practice. Editors are encouraged to follow these guidelines.

Abbreviations

The following abbreviations should be used where possible to conserve screen space.

Road Name Abbreviation TTS Expansion?
Avenue Ave Yes
Boulevard Blvd Yes
Broadway Bdwy Untested
Close Cl Yes
Court Ct Untested
Crescent Cr Yes [Sometimes pronounced "County Road"]
Drive Dr Yes
Garden Gdn Untested
Gardens Gdns Yes
Green Gn Untested
Grove Gr Untested
Junction (as in Motorway Jxx) J Fail - "Jay"
Lane Ln Yes
Mews
Mount Mt Untested
Place Pl Yes
Park Pk Untested
Rise
Road Rd Yes
Square Sq Untested
Street St Yes
Terrace Ter Yes

Notes:

  1. Roads like "The Avenue", "The Green" etc should not normally be abbreviated.
  2. TTS = Text To Speech for future Waze version support in Australia.

Road types

The following convention appears to be accurate and feasible to implement. Judgement and discretion may be necessary sometimes especially as some states have been slow in implementing the new national alphanumberic system.

Waze Road Type Australian Road Types
Freeway Freeway, motorway, expressway and tollway. There must be no intersections and there must be no access or exits except from ramps. Usually designated with "M" or "F" road numbers, for example "M2" or "F6".
Major Highway Usually designated with the letter "A" in most states (includes most "national highways" but not necessarily "national routes"). For example A31 is the Hume Highway, a major highway.
Minor Highway Usually designated with the letter "B" in most states. For example B75 is the Northern Hwy in Victoria and continues as the Cobb Hwy in NSW. Both are minor highways in Waze. Some roads can be a major highway in one section and a minor highway in a different section.
Primary Street Main Roads and Regional Roads connecting suburbs and towns, but not classified as highways. Also designated as "C" or "D" roads in some states.
Streets Urban streets and rural roads not identified above.

Dual Carriageways

The following convention should be followed where possible, although it is acknowledged that you may need to deviate from it in some circumstances.

A road can be split into be 2 one-way roads if any of the following conditions are met:

  1. The central reservation is > 5m
  2. There's a visible gap between average of all GPS traces
  3. It is split by physical barrier (Concrete, Armco, pedestrian barrier etc)

Pedestrian refuges and painted road separation (cross hatching that can be driven over) should not normally be split.

Motorway Carriageway Naming Convention

Whenever possible, on split roads, name carriageways with the direction of travel. Insert the direction of travel at the end of the road name:

Examples:
1. M1 (N)
2. A4 (W)
3. M25 (ACW)

This makes traffic and incident reports much more useful and helps with navigation.

Ramps (to/from Motorways and Dual Carriageways)

For the best balance between information, routing, reports and screen real estate the following convention should be used for the ramp road type:


Exit Ramps:

<Road Number> (<Direction>) (<Junction Number>) Exit (<” to ” Road Number 1, Road 2 …>)

Examples:
1. M54 (E) J4 Exit to A464
2. A46 (N) Exit to A6
3. M1 (S) J24 Exit to A453, A6
4. M1 (N) J24 Exit to A453
5. M4 (W) J4B Exit to M25
6. M5 (N) Exit to Services  


Entry Ramps:

“Entry to” <Road Number> (<Direction>) (<Junction Number>)

Examples:  
1. Entry to M54 (E) J4
2. Entry to A46 (N)
3. Entry to M1 (S) J24
4. Entry to M1 (N) J24
5. Entry to M25 (N) J15
6. Entry to M5 (N)


Notes:

  1. Fields marked in parenthesis (<field>) are optional.
  2. Onward roads should only added if they are shown on road signage as this is an aide to the driver to confirm they have the correct exit (e.g. Exit ramp example 4 which also has A6 and A50 not on signage). [Hint: look on streetview]
  3. Roads with clockwise or anticlockwise directions (e.g. M25) should have have ramp directions taken from signage which will typically be N, S, E or W (e.g. Entry ramp example 5). [Hint: look on streetview]
  4. Both example 6's above refer to Motorway Service Area (MSA) entry/exit ramps that do not have a junction number, where an MSA is integrated into a standard junction normal ramp naming applies.

Junction Naming

When naming/numbering junctions, particularly on motorways, please ensure the landmark is kept tight to the road system to ensure a tidy transfer to the client. The "snap-to" feature when adding landmarks via Papyrus should make this process easier!

Jct Name - Good1.PNG

or...

Jct Name - Good2.PNG


Large, freehand rectangles should be avoided...

Jct Name - Large1.PNG

Road Name & Number

Where a road exhibits both a road number and name the following convention should be used:

<Number> - <Name>

Examples:
1. A7 - Old Dalkeith Rd
2. A1 - Edinburgh Rd

This gives both a consistent appearance and allows a straightforward transfer if/when Waze UK moves to the official Department for Transport designations.

The same can also be said for adding the direction of travel on single/dual carriageways with an A-road designation in the form

<Number> (Direction) - <Name>

Examples:
1. A2 (W) - Dover Rd
2. A229 (N) - Cuxton Rd

Roundabouts

To aid navigation instructions, roundabouts should typically remain unnamed - where the client comes across a segment with no name it will use the next named segment as the next named instruction whilst retaining any turn signals.

If the roundabout does have a proper, signposted name, then this can be labelled using a 'Junction/Intersection' type landmark that fills the centre of the roundabout.

Motorway Service Area's

Motorway Service Area's (MSA) should be mapped according to the following convention:

  • Use "Ramps" on and off the motorway labelled as detailed in the Ramps section of the wiki.
  • Use "Streets" for all through roads (linking the ramps).
  • Use "Parking Lot Road" for Parking areas.
  • Use "Service Road" for Petrol Station forecourts.
  • Use "Private Road" for limited access roads (with no public right of way). Ensure that they are set to unknown connectivity, turn restrictions are set so that no-one can turn into the road and the segment(s) and connecting segments are locked to enforce the turn restrictions.
  • Do not add a City or Street name to any road with the exception of the ramps.
  • Set landmarks for the major buildings on site (i.e. Services Building, Fuel and Hotels etc).


A good example is the Strensham Services North on the M5 between J8 and J7. The currently selected segment in the link is the access road.


Note: To ensure that the turn restrictions are set on the limited access roads, select each junction node in turn and hit Q then W (if desired for other connectivity) to ensure that turns are only allowed on valid directions, then once you lock the segment(s) Waze should enforce the turn restrictions and not route the public down these roads.

For more information on how junction locking works in Waze see the forum thread: Modifying the lock option (and some explanations)

Bypass or By-pass?

Bypass.