Limited Access Interchange Style Guide: Difference between revisions Discussion View history

(→‎Feeder/Collector Cloverleaf: Completed initial coverage of feeder/collector cloverleafs)
(→‎Feeder/Collector Lanes: Added placeholder for complex Feeder/Collector)
Line 119: Line 119:


In this example, we have eliminated the ramp segment joining the two loops of the cloverleaf and the Feeder/Collector ramps.  Now they all connect at a single point and we are therefore able to restrict the turn that allowed drivers to use the Feeder/Collector as a bypass.
In this example, we have eliminated the ramp segment joining the two loops of the cloverleaf and the Feeder/Collector ramps.  Now they all connect at a single point and we are therefore able to restrict the turn that allowed drivers to use the Feeder/Collector as a bypass.
==== Complex Feeder/Collector ====
A Feeder/Collector is considered complex if there are multiple exits and entrances connected to the Feeder/Collector.
''(more to come)''

Revision as of 20:48, 22 August 2012

Limited Access Interchanges

See also: Wikipedia article on Road Interchanges

When two roads meet in a limited access interchange (any situation where travel between grade separated roads is facilitated by ramps or slip roads alone), extra care must be taken.

If an exit ramp lines up with an entrance ramp, care must be taken to restrict the straight through direction to prevent "ramp-to-ramp routing" where the routing engine may try to take a shortcut from the Freeway, to the exit ramp, to the entrance ramp, and back to the Freeway instead of staying on the Freeway. That motion is inefficient and may be illegal in certain jurisdictions.

Care must be taken to not enable all turns in any situation where ramps meet unless all possible flows of traffic have been considered!

We also have to pay attention to the Level of the road segments since there will typically be many bridges and overpasses for any limited access interchange. If two roads cross without connecting, their levels must be different.

The following sections discuss some of the common Interchange designs. Note that some Interchanges may be a hybrid of these basic designs where one side or quadrant of the interchange may differ from the others.

Diamond Interchange

See also: Diamond Interchange article on Wikipedia

Common in wide open spaces where land acquisition and geography are not concerns, this Interchange design has ramps equally distributed across all 4 quadrants.

In the simplest form, this can be represented as single connections from the ramps to the surface street.

Note: Be sure to restrict the straight through motion from the exit ramp onto the entrance ramp on the other side of the road. This will prevent the routing server from trying to route someone off the freeway just to get back on it. Even though it may be a legal direction for a vehicle, turn restrictions are only for controlling routing directions.

If the ramps connect to the surface street at multiple points (be sure to read How complex should ramps be?, we have to avoid ramp-to-ramp routing as well as illegal turns which should use another ramp. First we see the turns that must be restricted for the exit ramps:

Then we see what must be restricted for the entrance ramps:

Note on Levels: The single surface street segment between the inner most ramps should be either raised or lowered in relation to the freeway segments depending on the actual geography at the interchange.

Cloverleaf Interchange

See also: Cloverleaf Interchange article on Wikipedia

In a Cloverleaf Interchange, left turns are eliminated from all movements between the Freeway and the surface street. First check the exit ramps.

Then check the entrance ramps for illegal turns.

The connections to the Freeway segments may be treated in two ways:

  1. (top) we can have the inner entrance and exit ramps have their own junction nodes with the Freeway.
  2. (bottom) we can have the entrance and exit ramps share a single junction node with the Freeway. This allows us to eliminate the very short Freeway segment that may exist between the inner entrance and exit ramps.
    It is best to offset this shared junction onto the Entrance ramp side of the surface street. This prevents the junction from accidentally being connected to the surface street or looking like it does. We favor the Entrance ramp side, because this would result in a slightly earlier exit instruction which is of course preferred over a late exit instruction.

The determining factor of which design to use will partly depend on the actual size and scale of the specific interchange.

Note on Levels: The single surface street segment between the inner most ramps should be either raised or lowered in relation to the freeway segments depending on the actual geography at the interchange.

Folded Diamond

See also: Discussion of Folded Diamonds and A2/B2 Partial Cloverleafs on the Partial Cloverleaf Interchange article on Wikipedia

Geography or property ownership may prevent the ability for an interchange to be constructed with all ramps evenly distributed across the 4 quadrants of the interchange. When only two quadrants are used, it is typically called a Folded Diamond (basically a sub-type of a Partial Cloverleaf Interchange). The ramps may be all on one side (as in the examples in this section) or they may be located in diagonally opposed quadrants.

The unique situation presented by the Folded Diamond arrangement is having both Entrance and Exit ramps terminating on the same side of the surface street. Ideally both ramps should terminate on the same junction node to permit us to easily restrict the illegal and usually impossible ramp-to-ramp movement.

'

Like with a basic Diamond Interchange, often it will be necessary to represent the ramps making multiple connections to the surface street (Be sure to read How complex should ramps be?. Restrict all non-permitted turns.

Note on Levels: Similar to a basic Diamond interchange, in most cases only the segment of the surface street that crosses the Freeway segments will need to be adjusted up or down.

Single Point Urban Interchange (SPUI)

See also: Single Point Urban Interchange article on Wikipedia

A SPUI is a very space and flow efficient design, but it takes extra attention to ensure the turns are correct. And as the name indicates, ideally there should be a single junction in the center. You may need to tweak the geometry of segments a bit off of alignment from the real physical world, but it should be minor if the interchange is a true SPUI.

The outer branches of the exit ramps are very much like in the case of a diamond interchange:

Where things get complicated is the inner branches leading to the Single Point. You need to avoid ramp-to-ramp in two directions and a reverse flow turn. Note: The ramp-to-ramp motion to facilitate a U-Turn (the top left arrow in the image below) may or may not be allowed depending on the specific interchange. Please validate this turn.

Luckily the entrance ramp restrictions are similar to the diamond interchange:

If you were to look at all the restricted turns at once, you may get the false impression that something is very wrong. But as you now know, a SPUI has almost as many restricted turns as allowed ones.

Note on Levels: The two surface street segments (between the outer ramps and connected to the Single Point) and the 4 ramp segments connected to the single point should all be the same level, either one higher or one lower than the level of the freeway segments above/below the single point.

Feeder/Collector Lanes

These are lanes parallel to but physically separated from the lanes of a Limited Access Road that serve to keep merging traffic out of the flow of through traffic on the mainline Freeway.

Feeder/Collector Cloverleaf

This is a Cloverleaf interchange that is connected to a Feeder/Collector instead of directly to the main roadway. Here is an example which matches the physical world but has a major deficiency.

At first it appears that this layout allows everyone to get where they are going. The problem is that it allows MORE than it should. It is possible to exit the mainline Freeway and stay on the Feeder/Collector, bypassing the Cloverleaf, and merge back onto the mainline Freeway.

Although this may be a way to avoid traffic on the mainline Freeway, doing so is inefficient, may be unsafe, and is outright illegal in some areas. Therefore we need to tweak our design a little...

In this example, we have eliminated the ramp segment joining the two loops of the cloverleaf and the Feeder/Collector ramps. Now they all connect at a single point and we are therefore able to restrict the turn that allowed drivers to use the Feeder/Collector as a bypass.

Complex Feeder/Collector

A Feeder/Collector is considered complex if there are multiple exits and entrances connected to the Feeder/Collector.

(more to come)