User:Kentsmith9/WME segment length display View history

(→‎Metric precision and rounding: Clarified length accuracy)
 
(One intermediate revision by the same user not shown)
Line 16: Line 16:


== Metric precision and rounding ==
== Metric precision and rounding ==
The internal units are stored with an accuracy of 0.01 meters (0.0328 ft) or about 3/8-inch accuracy. However, the displayed units will be rounded up or down as needed to produce only whole meters. When the segment length reaches more than 999 meters, it switches to kilometers and changes the precision to 0.01 km (or 10 m). This means, you might nudge the end of a segment slightly, but the displayed length may not change if the nudge was inside of the 10 meter range of the kilometer display.
Segment lengths are stored internally with at least an accuracy of 0.01 meters (1 cm, 0.0328 ft or about 3/8-inch). However, the displayed units will be rounded up or down as needed to produce only whole meters. When the segment length reaches more than 999 meters, it switches to kilometers and changes the precision to 0.01 km (or 10 m). This means, you might nudge the end of a segment slightly, but the displayed length may not change if the nudge was inside of the 10 meter range of the kilometer display.
 
{{mbox|type=note|text=It has been noted that it is possible to initially see a granularity of only 1 millimeter when initially creating a segment before saving it, but that resolution seems to vanish after the first save.}}
 


The meters displayed are rounded to the nearest whole number, with a minimum savable segment size of 1 meter (3.28 feet). Drawing or shrinking a segment any shorter than that will result in a save error. Segments shorter than {{:Segment length/Minimum}} will not accurately track speed data and should be avoided. See this discussion on [[Segment_length#Too_short|minimum segment length]] for more information.
The meters displayed are rounded to the nearest whole number, with a minimum savable segment size of 1 meter (3.28 feet). Drawing or shrinking a segment any shorter than that will result in a save error. Segments shorter than {{:Segment length/Minimum}} will not accurately track speed data and should be avoided. See this discussion on [[Segment_length#Too_short|minimum segment length]] for more information.
Line 123: Line 120:
|-
|-
|}
|}
{{NeedImage|Drawing of the reality of segment lengths compared to the stepped output of the whole numbers including the rounding.}}


== Imperial precision and rounding ==
== Imperial precision and rounding ==
Line 218: Line 212:


'''Meters to Miles'''
'''Meters to Miles'''
:<code>Integer( Integer( TrueSegmentLength * 3.28084 + 0.5 ) / 52.8 + 0.5 ) ) / 100</code><br />
:<code>Integer( TrueSegmentLength * 3.28084 / 52.8 + 0.5 ) / 100</code><br />




Line 230: Line 224:
! Displayed result (mi)
! Displayed result (mi)
|-
|-
| 4997.04
| 4988.96
| 4.99
| 4.98
| 3.10
| 3.10
|-
|-
| 4997.05
| 4988.97
| 4.98
| 3.11
|-
| 4999.49
| 4.99
| 4.99
| 3.11
| 3.11
|-
|-
| 4997.04
| 4999.50
| 5.00
| 5.00
| 3.10
| 3.11
|-
|-
| 4997.05
| 5000.00
| 5.00
| 5.00
| 3.11
| 3.11
|-
|-
| 5000.00
| 5005.05
| 5.00
| 5.00
| 3.11
| 3.11
|-
| 5005.06
| 5.00
| 3.12
|-
|-
| 5009.49
| 5009.49
| 5.00
| 5.00
| 3.11
| 3.12
|-
|-
| 5009.50
| 5009.50
| 5.01
| 3.11
|-
| 5013.19
| 5.01
| 3.11
|-
| 5013.20
| 5.01
| 5.01
| 3.12
| 3.12
|-
|}
|}


== Custom precision script for WME ==
== Custom precision script for WME ==
Users in the Waze editing community have developed scripts that can be loaded into the browser to enable additional functionality not available in the basic WME available from Waze. One such script is the [[Scripts/WME_True_Segment_Length|WME True Segment Length]]. This script will display the true length of the segment in both metric and imperial units with two decimal places of accuracy.
Users in the Waze editing community have developed scripts that can be loaded into the browser to enable additional functionality not available in the basic WME available from Waze. One such script is the [[Scripts/WME_True_Segment_Length|WME True Segment Length]]. This script will display the true length of the segment in both metric and imperial units with two decimal places of accuracy.

Latest revision as of 14:48, 2 June 2017

The Waze platform is based on metric units and each Waze application (WME and the client app) translates that into imperial units as required. Both display interfaces have a loss of accuracy in the displayed segment length due to rounding.

The following information is only focused on the WME application and will not be covering the impact on the client app.


Overview

All Waze segment length information is based on metric unit measurements.

When a user selects the metric unit measurement system from WME, the interface displays a whole metric unit rounded (up or down), not truncated.

When a user selects the imperial unit measurement system from WME, the interface simply translates the already rounded metric units into imperial units. WME displays two decimal places of accuracy for the translation from the rounded numbers, giving a false sense of precision. Note that any third decimal unit is also rounded as needed.

Metric precision and rounding

Segment lengths are stored internally with at least an accuracy of 0.01 meters (1 cm, 0.0328 ft or about 3/8-inch). However, the displayed units will be rounded up or down as needed to produce only whole meters. When the segment length reaches more than 999 meters, it switches to kilometers and changes the precision to 0.01 km (or 10 m). This means, you might nudge the end of a segment slightly, but the displayed length may not change if the nudge was inside of the 10 meter range of the kilometer display.

The meters displayed are rounded to the nearest whole number, with a minimum savable segment size of 1 meter (3.28 feet). Drawing or shrinking a segment any shorter than that will result in a save error. Segments shorter than 19.69 ft (6 m) will not accurately track speed data and should be avoided. See this discussion on minimum segment length for more information.

Meters are rounded with the following formula:

Integer( TrueSegmentLength + 0.5 )

This results in the following:

Meters
True length (m) Formula Steps Displayed result (m)
4.49 Integer(4.49 + 0.5) Integer(4.99) 4
4.50 Integer(4.5 + 0.5) Integer(5.0) 5
4.99 Integer(4.99 + 0.5) Integer(5.49) 5
5.00 Integer(5 + 0.5) Integer(5.5) 5
5.49 Integer(5.49 + 0.5) Integer(5.99) 5
5.50 Integer(5.5 + 0.5) Integer(6.0) 6

The formula for the kilometer range is more complex. Note the precision is still based on the 2 decimal places for the meters:

Integer( ( TrueSegmentLength + 0.5 ) / 10 ) / 100
Int = Integer in the table below

This results in the following:

Kilometers
True length (m) Formula Steps Displayed result (km)
1004.99 Int( ( 1004.99 + 5 ) / 10 ) / 100 Int( 1009.99 / 10 ) / 100 Int( 100.999 ) / 100 100 / 100 1.00
1005.00 Int( ( 1005 + 5 ) / 10 ) / 100 Int( 1010 / 10 ) / 100 Int( 101 ) / 100 101 / 100 1.01
1009.99 Int( ( 1009.99 + 5 ) / 10 ) / 100 Int( 1014.99 / 10 ) / 100 Int( 101.499 ) / 100 101 / 100 1.01
1010.00 Int( ( 1010 + 5 ) / 10 ) / 100 Int( 1015 / 10 ) / 100 Int( 101.5 ) / 100 101 / 100 1.01
1014.99 Int( ( 1014.99 + 5 ) / 10 ) / 100 Int( 1019.99 / 10 ) / 100 Int( 101.999 ) / 100 101 / 100 1.01
1015.00 Int( ( 1015 + 5 ) / 10 ) / 100 Int( 1020 / 10 ) / 100 Int( 102 ) / 100 102 / 100 1.02

Imperial precision and rounding

When changing the WME display to imperial, there is no change to the underlying segment unit value. The WME interface simply translates all the already rounded metric displayed values into the equivalent imperial values out to two decimal places. This has the negative impact of purporting a high degree of precision when in fact it is without basis.

The translation from metric to imperial is done by the following formula:

Integer( RoundedDisplayMeters * 328.084 + 0.5 ) / 100

This results in the following:

Feet
Rounded length (m) Formula Steps Displayed result (ft)
4 Integer( 4 * 328.084 + 0.5 ) / 100 Integer( 1312.836) / 100 1312 / 100 13.12
5 Integer( 5 * 328.084 + 0.5 ) / 100 Integer( 1640.920) / 100 1640 / 100 16.4
6 Integer( 6 * 328.084 + 0.5) / 100 Integer( 1969.004) / 100 1969 / 100 19.69


Now look at what happened to the original unit as measured in feet after it is rounded in metric and then converted back to imperial. You can see the back and forth translations amplify the error, yet continue to provide a false sense of accuracy with the two decimal places:

This results in the following:

The Amplified False Accuracy with Feet
True length (ft) True length (m) Rounded metric Displayed result (ft)
14.73 4.49 4 13.12
14.76 4.50 5 16.4
16.37 4.99 5 16.4
16.40 5.00 5 16.4
18.01 5.49 5 16.4
18.04 5.50 6 19.69

Because WME will show the value 5 meters or 16.4 feet for wide range of values both above and below 5 meters, that value cannot reliably be used to ensure a segment is above or below a server threshold of 5 meters or 16.4 feet. Therefore, to guarantee you are above a 5 meter threshold you must select 6 meters or 19.69 feet. Similarly, if you want to ensure you are below a 5 meter threshold you must select 4 meters or 13.12 feet.

Differences between kilometers and miles

When the units are large enough, the display will convert the displayed units to kilometers or miles depending upon which unit type is set to display in WME.

As mentioned earlier, the base unit measurement continues to be meters when displaying kilometers. The same is true with the imperial system and the base unit of meters is converted to miles. The displayed value is translated from that base unit with the following two formulas:

Meters to Kilometers (shown earlier)

Integer( ( TrueSegmentLength + 0.5 ) / 10 ) / 100


Meters to Miles

Integer( TrueSegmentLength * 3.28084 / 52.8 + 0.5 ) / 100


This results in the following displayed values (the formula steps have been excluded for simplicity in the table):

Kilometers and Miles
True length (m) Displayed result (km) Displayed result (mi)
4988.96 4.98 3.10
4988.97 4.98 3.11
4999.49 4.99 3.11
4999.50 5.00 3.11
5000.00 5.00 3.11
5005.05 5.00 3.11
5005.06 5.00 3.12
5009.49 5.00 3.12
5009.50 5.01 3.12

Custom precision script for WME

Users in the Waze editing community have developed scripts that can be loaded into the browser to enable additional functionality not available in the basic WME available from Waze. One such script is the WME True Segment Length. This script will display the true length of the segment in both metric and imperial units with two decimal places of accuracy.