Introduction
This forms part of UK Editing Best Practice. Editors are encouraged to follow these guidelines.
See the following forum posts for discussion:
Abbreviations
The following abbreviations should be used where possible to conserve screen space.
| Road Name | Abbreviation | TTS Expansion? |
|---|---|---|
| Avenue | Ave | Yes |
| Boulevard | Blvd | Yes |
| Broadway | Bdwy | Untested |
| Close | Cl | Yes |
| Court | Ct | Untested |
| Crescent | Cr | Yes [Sometimes pronounced "County Road"] |
| Drive | Dr | Yes |
| Garden | Gdn | Untested |
| Gardens | Gdns | Yes |
| Green | Gn | Untested |
| Grove | Gr | Untested |
| Junction (as in Motorway Jxx) | J | Fail - "Jay" |
| Lane | Ln | Yes |
| Mount | Mt | Untested |
| Place | Pl | Yes |
| Park | Pk | Untested |
| Road | Rd | Yes |
| Square | Sq | Untested |
| Street | St | Yes |
| Terrace | Ter | Yes |
Notes:
- Roads like "The Avenue", "The Green" etc should not normally be abbreviated.
- TTS = Text To Speech for future Waze version support in UK.
Road types
The following convention should be followed where possible, although it is acknowledged that you may need to deviate from it in some circumstances.
| Waze Road Type | UK Road Types |
|---|---|
| Freeway | Motorway |
| Major Highway | Trunk roads (other than motorways) as defined below. |
| Minor Highway | Non-trunk A-class roads or dual-carriageway B-class |
| Primary Street | Other B-class roads and roads carrying heavier traffic, often seen on Ordnance survey maps in yellow or orange. |
| Streets | Urban Streets, Low traffic rural roads |
Scottish Trunk Roads (Traffic Scotland)
English Trunk Roads (Highways Agency) | London Trunk Roads (Transport for London)
Dual Carriageways
The following convention should be followed where possible, although it is acknowledged that you may need to deviate from it in some circumstances.
A road can be split into be 2 one-way roads if any of the following conditions are met:
- The central reservation is > 5m
- There's a visible gap between average of all GPS traces
- It is split by physical barrier (Concrete, Armco, pedestrian barrier etc)
Pedestrian refuges and painted road separation (cross hatching that can be driven over) should not normally be split. Be aware there are a lot of these that were created as split roads during the UK Base-map import, these usually need merging to be a single two-way road.
Motorway Carriageway Naming Convention
Whenever possible, on split roads, name carriageways with the direction of travel. Insert the direction of travel at the end of the road name:
Examples: 1. M1 (N) 2. A4 (W) 3. M25 (ACW)
This makes traffic and incident reports much more useful and helps with navigation.
Ramps (to/from Motorways and Dual Carriageways)
For the best balance between information, routing, reports and screen real estate the following convention should be used for the ramp road type:
Exit Ramps:
<Road Number> (<Direction>) (<Junction Number>) Exit (<” to ” Road Number 1, Road 2 …>)
Examples: 1. M54 (E) J4 Exit to A464 2. A46 (N) Exit to A6 3. M1 (S) J24 Exit to A453, A6 4. M1 (N) J24 Exit to A453 5. M4 (W) J4B Exit to M25
Entry Ramps:
“Entry to” <Road Number> (<Direction>) (<Junction Number>)
Examples: 1. Entry to M54 (E) J4 2. Entry to A46 (N) 3. Entry to M1 (S) J24 4. Entry to M1 (N) J24 5. Entry to M25 (N) J15
Notes:
- Fields marked in parenthesis (<field>) are optional.
- Onward roads should only added if they are shown on road signage as this is an aide to the driver to confirm they have the correct exit (e.g. Exit ramp example 4 which also has A6 and A50 not on signage). [Hint: look on streetview]
- Roads with clockwise or anticlockwise directions (e.g. M25) should have have ramp directions taken from signage which will typically be N, S, E or W (e.g. Entry ramp example 5). [Hint: look on streetview]
Junction Naming
When naming/numbering junctions, particularly on motorways, please ensure the landmark is kept tight to the road system to ensure a tidy transfer to the client. The "snap-to" feature when adding landmarks via Papyrus should make this process easier!
or...
Large, freehand rectangles should be avoided...
Road Name & Number
Where a road exhibits both a road number and name the following convention should be used:
<Number> - <Name>
Examples: 1. A7 - Old Dalkeith Rd 2. A1 - Edinburgh Rd
This gives both a consistent appearance and allows a straightforward transfer if/when Waze UK moves to the official Department for Transport designations.
The same can also be said for adding the direction of travel on single/dual carriageways with an A-road designation in the form
<Number> (Direction) - <Name>
Examples: 1. A2 (W) - Dover Rd 2. A229 (N) - Cuxton Rd
Roundabouts
To aid navigation instructions, roundabouts should typically remain unnamed - where the client comes across a segment with no name it will use the next named segment as the next named instruction whilst retaining any turn signals.
If the roundabout does have a proper, signposted name, then this can be labelled using a 'Junction/Intersection' type landmark that fills the centre of the roundabout.
- For further advice, see Editing Junctions and Roundabouts (United Kingdom)
Motorway Service Area's
Motorway Service Area's (MSA) should be mapped according to the following convention:
- Use "Ramps" on and off the motorway labelled as detailed in this wiki.
- Use "Streets" for all through roads (linking the ramps).
- Use "Parking Lot Road" for Parking areas.
- Use "Service Road" for Petrol Station forecourts.
- Use "Private Road" for limited access roads (with no public right of way). Ensure that they are set to unknown connectivity, turn restrictions are set so that no-one can turn into the road and the segment(s) and connecting segments are locked to enforce the turn restrictions.
- Do not add a City or Street name to any road with the exception of the ramps.
- Set landmarks for the major buildings on site (i.e. Services Building, Fuel and Hotels etc).
A good example is the Strensham Services North on the M5 between J8 and J7. The currently selected segment in the link is the access road.
Note: To ensure that the turn restrictions are set on the limited access roads, select each junction node in turn and hit Q then W (if desired for other connectivity) to ensure that turns are only allowed on valid directions, then once you lock the segment(s) Waze should enforce the turn restrictions and not route the public down these roads.
For more information on how junction locking works in Waze see the forum thread: Modifying the lock option (and some explanations)
Bypass or By-pass?
Bypass.